Monarch IP – Aluminium

An IP66, aluminium, multiple application enclosure & switchboard building system suitable for a wide variety of applications.
AS/NZS 61439
Monarch IP – Aluminium
Australian Made
Australian Made

Product Information

Applications

Designed to be the ultimate in flexibility the Monarch IP system is suitable for small motor control applications, lighting, CT metering and small switchboards (to form 2).

Features

  • IP66 protection rating – more info on IP ratings
  • Vertical body and door rails
  • Earth strap kit comes as standard
  • Reversible doors (right hand hinging as standard)
  • Multiple mounting options providing the flexibility to install equipment in almost any position
  • Wide range of accessories for added versatility in equipment application
  • Region D wind rated to AS1170.2-2002: Structural design actions – Wind actions

Construction

  • Body – Aluminium
  • Body thickness – 2.5mm
  • Polyurethane gasket (formed in place)
  • Powdercoated light grey RAL7035 paint finish or,
  • Ripple Orange – X15 (denoted by /RO in the part number code below)

Inclusions

  • C rail mountings
  • Gland plate (fitted internally or externally)
  • 7mm square turnbuckle lock (below 1600mm high)
  • Lockable L handles (above 1600mm high)
  • 3-point locking (600mm high and above)
  • Removable back (400mm deep and above)
  • Door rails
  • Earth strap kit

Also available with Viewing Window Doors

DownloadsAccessoriesMore ProductsEnquiryOnline StockistsLocal Stockists

Order Guide

Smaller Enclosures Enclosure Selector Larger Enclosures

Part NumberHeight (mm)Width (mm)Depth (mm)WeightCAD BlocksEnquiry
Standard X15 Orange
IP13132/AIP13132/ARO4074072726dwgEnquiry
IP13212/AIP13212/ARO4076072729dwgEnquiry
IP13214/AIP13214/ARO40760740211dwgEnquiry
IP21132/AIP21132/ARO6074072729dwgEnquiry
IP21212/AIP21212/ARO60760727211dwgEnquiry
IP21214/AIP21214/ARO60760740215dwgEnquiry
IP21292/AIP21292/ARO60780727213dwgEnquiry
IP21294/AIP21294/ARO60780740218dwgEnquiry
IP21295/AIP21295/ARO60780750221dwgEnquiry
IP25254/AIP25254/ARO70770740218dwgEnquiry
IP29212/AIP29212/ARO80760727213dwgEnquiry
IP29214/AIP29214/ARO80760740218dwgEnquiry
IP29215/AIP29215/ARO80760750243dwgEnquiry
IP29216/AIP29216/ARO80760760227dwgEnquiry
IP29294/AIP29294/ARO80780740221dwgEnquiry
IP37212/AIP37212/ARO100760727216dwgEnquiry
IP37254/AIP37254/ARO100770740222dwgEnquiry
IP37294/AIP37294/ARO100780740225dwgEnquiry
IP45212/AIP45212/ARO120760727218dwgEnquiry
IP45214/AIP45214/ARO120760740224dwgEnquiry
IP45215/AIP45215/ARO120760750221dwgEnquiry
IP45216/AIP45216/ARO120760760236dwgEnquiry
IP45294/AIP45294/ARO120780740229dwgEnquiry
IP45295/AIP45295/ARO120780750232dwgEnquiry
IP61214/AIP61214/ARO160760740230dwgEnquiry
IP61215/AIP61215/ARO160760750227dwgEnquiry
IP61216/AIP61216/ARO160760760240dwgEnquiry
IP61294/AIP61294/ARO160780740237dwgEnquiry
IP61295/AIP61295/ARO160780750240dwgEnquiry
IP61296/A—160780760243Enquiry
IP69214/AIP69214/ARO180760740234dwgEnquiry
IP69215/AIP69215/ARO180760750234dwgEnquiry
IP69294/AIP69294/ARO180780740240dwgEnquiry
IP69295/AIP69295/ARO180780750244dwgEnquiry
IP77135/AIP77135/ARO200740750241Enquiry
IP77136/AIP77136/ARO200740760244Enquiry
IP77214/AIP77214/ARO200760740237dwgEnquiry
IP77215/AIP77215/ARO200760750237dwgEnquiry
IP77216/AIP77216/ARO200760760245dwgEnquiry
IP77218/AIP77218/ARO200760780260Enquiry
IP77294/AIP77294/ARO200780740244dwgEnquiry
IP77295/AIP77295/ARO200780750248dwgEnquiry
IP77296/AIP77296/ARO200780760252dwgEnquiry
IP77298/AIP77298/ARO200780780263Enquiry

Smaller Enclosures Enclosure Selector Larger Enclosures

Accessories

Accessories

  • Lock options such as L handle
  • Metal mounting pans
  • Insulated mounting pans
  • Double hinged insulating panels
  • Hinged escutcheons
  • Fixed escutcheons
  • Gland plates
  • Shelves
  • Plinths
  • Rainhood
  • Vent kit
  • Vent hoods (IPVK/S)
  • Lifting brackets
  • Wall mounting brackets
  • Rails (‘C’, DIN, UV, escutcheon and busbar)
  • Climate control equipment

Climate Control

For more information see our Climate Control page (opens in new tab)

Lock Options

Standard

Catalogue No.TypeMaterialCommentsLock Insert TypeKeyImage
IP020/PSTurnbucklePowdercoated with SS InsertStandard7mm Square Stainless SteelSKZTurnbuckle Lock - Powdercoated Steel with 7mm Square Stainless Steel Insert
NI028S/STurnbuckleStainless SteelStandard on Bowen BW, option on all others8mm Square Slotted Stainless SteelSK8Turnbuckle Lock - Stainless Steel, 8mm Square Slotted
IP050L Handle - LockableChromed SteelStandard 1600mm or higher, Option less than 1600mmKey Code 92268SK3L Handle Lockable - Chrome Steel Key 92268

Options

Catalogue No.TypeMaterialCommentsLock Insert TypeKeyImage
IP020/STurnbuckleStainless SteelOption7mm Square Stainless SteelSKZTurnbuckle Lock - Stainless Steel with 7mm Square
NI028S/STurnbuckleStainless SteelStandard on Bowen BW, option on all others8mm Square Slotted Stainless SteelSK8Turnbuckle Lock - Stainless Steel, 8mm Square Slotted
IP030Wing Knob - LockableOptionKey Code 92268SK3Lockable Wing Knob - 92268 Key
IP030/CL001Wing Knob - LockableOptionKey Code CL001SK3Lockable Wing Knob - 92268 Key
IP030/L003Wing Knob - LockableOptionKey Code L003SK3Lockable Wing Knob - 92268 Key
IP111Wing Knob - Non-lockableOptionNon-lockable Wing Knob
IP040T Handle - LockableChromed SteelOptionKey Code 92268SK3T Handle Lockable - Chromed Steel 92268 Lock
IP050L Handle - LockableChromed SteelStandard 1600mm or higher, Option less than 1600mmKey Code 92268SK3L Handle Lockable - Chrome Steel Key 92268
IP052L Handle - PadlockableChromed SteelOptionPadlockL Handle - Padlockable, Chrome Steel
IP052/SL Handle - PadlockableStainless SteelOptionPadlockL Handle Padlockable - Stainless Steel
IP060Swing Handle - PadlockableChromed SteelOptionPadlockSwing Handle - Padlockable Chrome Steel
IP060/SSwing Handle - PadlockableStainless SteelOptionPadlockSwing Handle Padlockable - Stainless Steel
Inserts for Turnbuckle Locks - Optional
Catalogue No.ProductMaterialLock Insert TypeKey
LKINS3PInsertSteel3mm Double Bit PinSKZ
LKINS3P/SInsertStainless Steel3mm Double Bit PinSKZ
LKINS8SInsertSteel8mm SquareSK8
LKINS8S/SInsertStainless Steel8mm SquareSK8
LKINS8SS/SInsertStainless Steel8mm Square SlottedSK8
LKINS8TInsertSteel8mm TriangleSKZ
LKINS8T/SInsertStainless Steel8mm TriangleSKZ

AS/NZS 61439 Compliance

AS/NZS 61439 is the new series of standards for low-voltage (LV) switchgear and control gear assemblies. For more information on whether you need to comply see our AS/NZS 61439 page.

Click the bar below the requirements and responsibilities for complaince with AS/NZS 61439 for this enclosure.

The following definitions apply to this table: -

  • Original Manufacturer* - Switchboard designer and manufacturer of the switchboard enclosure.
  • Assembly Manufacturer* - A switchboard builder.
  • Original Equipment Manufacturer - The company who manufactured the switchgear used in final assembly.

*The original manufacturer and assembly manufacturer can be the same company or different companies.

If you are a SWITCHBOARD BUILDER this means you are the ASSEMBLY MANUFACTURER and you may be the ORIGINAL MANUFACTURER too. Any switchgear you order will need to be covered by the requirements of the Original Equipment Manufacturer.

B&R has some (but not all) of the responsibilities of the ORIGINAL MANUFACTURER.

If you are an END USER of the equipment you can see who has responsibility from these definitions.

NoCharacteristic to be CheckedClauseResponsibilityComments
Resistance to corrosion  10.2.2Original ManufacturerTesting has shown Zinc-coated steel resists corrosion to 1000 hours of neutral salt spray, exceeding the 61Compliance. Further verification has been performed by an external NATA laboratory to severity level B (outdoor environments).
Thermal stability (relates to non-metal enclosures)  10.2.3.1Original ManufacturerMetal enclosures have no thermal stability requirements.
Resistance to abnormal heat and fire (due to internal electric effect)  10.2.3.2Original ManufacturerInsulation materials have been verified by external NATA laboratory.
Resistance to ultra-violet (UV) radiation  10.2.4Original ManufacturerMetal enclosures do not require UV verification except when painted. B&R use industrial grade powder-coat paint which incorporates UV stabilisation and is certified by our supplier.
Lifting  10.2.5Original ManufacturerLifting requirements have been verified by external NATA laboratory.
Mechanical Impact  10.2.6Original ManufacturerInternal testing verifies that enclosures exceeds IK10 required.
Marking  10.2.7Assembly ManufacturerLabels supplied by B&R are manufactured from plastic laminated materials and meet all 61Compliance requirements. Switchboard builders need also to take note of 61Compliance requirements for a labelling. Markings have been verified by external NATA laboratory.
2Degree of protection of enclosures (IP)10.3Original ManufacturerAll IP requirements have been verified by external NATA laboratory.
3Clearances10.4Assembly ManufacturerClearances have been verified by external NATA laboratory.
However, the SBB must also ensure compliance by ensuring correct clearances are maintained as per the Standard and original equipment manufacturers installation instructions.
4Creepage distances10.4Assembly Manufacturer
5Protection against electric shock and integrity of protective circuits10.5
Effective continuity between the exposed conductive parts of the ASSEMBLY and the protective circuit   10.5.2Assembly ManufacturerProtective circuits have been verified by external NATA laboratory.
However, the SBB must also ensure effective continuity between exposed conductive parts of an assembly and protective circuits are maintained (less than 0.1ohm).
Short-circuit withstand strength of the protective circuit   10.5.3Original ManufacturerProtective circuits short-circuit withstand strength has been verified by external NATA laboratory.
However, the SBB must also ensure compliance by ensuring correct implementation of protective circuits as per the Standard and original equipment manufacturers installation instructions.
6Incorporation of switching devices and components10.6Assembly ManufacturerThis is the responsibility of the SBB; however, it is a requirement that the SBB follows guidance from the original equipment manufacturer (OEM). The advice and guidance of the OEM such as B&R and switchgear manufacturers needs to be adhered to while maintaining compliance to Standards and State based Regulations and Service and Installation Rules (SIR).
7Internal electrical circuits and connections10.7Assembly Manufacturer
8Terminals for external conductors10.8Assembly Manufacturer
9Dielectric Properties10.9
Power-frequency withstand voltage  10.9.2Original ManufacturerWithstand voltages have been verified by external NATA laboratory.
However, the SBB must also ensure effective assembly of the switchboard, adhering to all OEM installation Instructions.
Impulse withstand voltage  10.9.3Original Manufacturer
10Temperature-rise limits10.1Assembly ManufacturerThe switchboard designer (either the Original Manufacturer or the SBB), must calculate temperature rise as each design may be different. For switchboards below 1600A rating, AS/NZS 60890 can be used from first principles.
11Short circuit withstand strength10.11Original ManufacturerTested and certified by an external NATA laboratory and passed to a rating of 50kA/1s.
12Electromagnetic compatibility (EMC)10.12Original Equipment ManufacturerEquipment installed in switchboards must comply with the immunity requirements of the relevant product or generic EMC standard. The SBB must obtain from the OEM the specific performance criteria of the equipment based on the acceptance criteria given in the relevant standard.
13Mechanical operation10.13Original Equipment ManufacturerMechanical operation relates to situations where switchgear operation has been changed beyond their original approval. However, SBB must ensure compliance if modifications have been made.